How much does a garage door cost?

Garage-door pricing splits into two very different conversations. A repair (a broken spring, a frayed cable, a door off its track) is a known, repeatable job that most homeowners pay $150–$600 for. A new door is a bigger, more configurable purchase: anywhere from a $1,000 basic steel single to an $8,000+ custom wood or full-view glass build. Here is what each costs in 2026, why the numbers swing so widely, how the 2025 steel tariffs reshaped the market, and how to read a quote that lands at the high end.

What a new garage door costs

A new door installed runs $700–$2,700 for a typical single-car job and reaches well past $4,000 for premium doubles. Most homeowners replacing a single-car door pay $1,000–$2,000; a double-car door usually runs $1,800–$3,500. National averages cluster around $2,200 for a single and $3,500 for a double, but the headline number is set by two choices: material and size.

Material is the single biggest lever on the door itself:

• Steel: the most common and most affordable, roughly $650–$3,200 for the door. It is the floor that most quotes start from.
• Aluminum: $600–$2,900, light and rust-resistant, popular in coastal and humid markets.
• Composite / fiberglass: mid-range, typically priced between steel and wood, with the wood look and less upkeep.
• Real wood: $900–$4,500+ for the door alone, the premium tier; carriage-style and custom builds push it higher still.
• Full-view glass and aluminum: the most expensive look, often driving a complete door into the $4,000–$8,000+ range installed.

Style stacks on top of material. A standard sectional door (the panels that roll up on tracks) is the baseline and the most common; roll-up and carriage-house styles cost more, and a true side-hinged or tilt-up carriage build is at the top end. Insulation is the other upgrade that matters: an insulated door costs roughly $400–$800 more than a non-insulated one but can cut energy loss in an attached garage by a meaningful margin, which is why it is the most common upsell on a new-door quote.

What moves your garage door quote

Two identical-looking doors two towns apart can quote very differently. The real drivers, in roughly the order they matter:

1. Door size and configuration. A single-car door is the baseline; a double-car door costs more and a three-car (or two separate doubles) more again. Size sets both the material and the labor.
2. Material grade. Steel is the floor; aluminum and composite sit in the middle; real wood and full-view glass are the ceiling. This is the widest single swing on the door itself.
3. Insulation level. Insulated doors add roughly $400–$800, and polyurethane cores (higher R-value) cost more than polystyrene.
4. Opener. Adding or replacing an opener runs $300–$800 installed, depending on drive type and whether it's a smart/Wi-Fi unit.
5. The 2025 steel and aluminum tariffs. Tariffs jumped from 25% to 50% effective June 4, 2025, and steel and aluminum are 40–60% of what a door costs to make. Manufacturers passed the increase through; every 2026 quote sits above 2024 levels.
6. Regional labor market. West Coast and Northeast metros run highest on installed labor; the South and rural Midwest run lowest. The gap is real and shows up on every line.
7. Structural and framing work. If the opening needs reframing, a new header, or drywall repair, add $150–$1,000+.
8. Old-door haul-away and disposal. Most full-replacement quotes include removing and disposing of the old door, but confirm it; it's a common surprise add-on.
9. Permits. Some municipalities require a permit for a full door or opener install, $50–$200, usually not included in the contractor's quote.
10. Emergency and after-hours service. Same-day, weekend, or holiday calls typically add a $100–$200 surcharge or bill at 1.5–2× the standard labor rate.

Repair price bands, line by line

Repairs are the other half of the business, and most of them are far cheaper than a new door. The typical repair runs $150–$600, with the full spread from a $80 sensor adjustment to an $860 panel swap. These are rough 2026 customer-facing ranges; the part and your market set the real number.

• Torsion spring replacement: $200–$350 for a single spring; a pair commonly $300–$600, and high-cycle springs higher. The most common failure on an older door.
• Extension spring replacement: $150–$300 for a pair, the lighter-duty spring system, cheaper than torsion.
• Cable replacement: $150–$350 for the pair, parts and labor. Cables and springs often fail together.
• Roller / hinge / hardware replacement: $75–$250 depending on how many rollers and the quality grade (nylon vs. steel).
• Track repair or replacement: $125–$450: a bent-section straighten at the low end, full track replacement at the high end.
• Off-track door reset: $125–$300 to re-seat a door that has jumped its tracks (a safety issue; don't force it).
• Sensor alignment / safety-eye fix: $75–$150, often the cheapest service call.
• Single panel replacement: $250–$860 per panel ($350–$900 for some materials); older doors may have discontinued panels that force a full replacement.
• Opener motor / logic-board repair: $100–$350 for a fix; a full opener replacement runs $300–$800 installed.
• Tune-up / annual maintenance: $75–$150: lube, balance check, hardware tighten, sensor test.
• Service-call / diagnostic fee: $100–$200, frequently credited toward the repair if you book the work.

Grouped by scope, that's roughly: minor service (sensor, tune-up, off-track) $75–$300; common part replacements (springs, cables, rollers, tracks) $150–$600; and the larger fixes (panel swap, opener replacement) $300–$860+. Anything past that and you're usually comparing a repair against a full new door.

A note on the opener

Openers are quoted by drive type. A chain-drive opener is the cheapest unit ($150–$250) but the noisiest; a belt-drive ($160–$500) is quieter and a better fit when there's living space above the garage; a screw-drive ($250–$400) splits the difference; and direct-drive / smart Wi-Fi units ($220–$400+) add app control and the quietest operation. Installed, most opener jobs land at $300–$800 all-in, with the average around $380. LiftMaster's 2025 list-price increase (about 25%, plus a later surcharge) is part of why those numbers are up.

When it costs more and when it costs less

If you want to know which side of the range your job will land on, this is the honest breakdown.

You'll pay toward the high end when…

• The door is real wood, full-view glass, or a custom carriage build rather than basic steel.
• It's a double or three-car door rather than a single.
• You're adding insulation, a new opener, and smart controls in the same job.
• The opening needs reframing or structural work.
• You're in a West Coast or Northeast metro with high labor rates.
• It's an emergency or after-hours call.
• The repair is a discontinued panel that forces a full replacement.

You'll pay toward the low end when…

• It's a basic non-insulated steel single-car door with a clean swap.
• The repair is a single spring, a sensor alignment, or an off-track reset.
• The existing opener and tracks are reusable.
• You're in the South or rural Midwest where labor runs lower.
• You book during normal hours and bundle the service-call fee into the repair.

The single biggest swing on a new door is the material-and-size combination: a basic steel single can come in near $1,000, while a wood or glass double with a new opener can clear $6,000–$8,000 for essentially the same opening. On repairs, the biggest variable is whether a part can be fixed in isolation or drags the rest of the system with it: a broken spring is routine, but a spring that took the cables and a panel with it is a different invoice.

Garage door costs by region

Region is one of the first things that moves a quote, mostly through labor rates. These bands reflect installed-labor differences and should be treated as directional, not a precise city-by-city matrix.

• West Coast (CA, OR, WA): installed labor roughly $180–$250/visit-equivalent; the highest in the country, driven by licensing, urban travel fees, and cost of living. Total door jobs run above the national average.
• Northeast (NY, MA, CT, NJ): labor around $170–$240; dense cities and tight access extend service times and push totals up.
• Midwest (IL, OH, MN): labor around $130–$190; tracks national averages closely with consistent technician availability, though rural areas may add a travel surcharge.
• South / Southeast (GA, TN, NC, TX): labor around $120–$180; strong competition among independent installers keeps pricing the lowest, partly offset by humidity that favors aluminum and more frequent hardware service.
• Mountain West (CO, UT): generally near the national midrange, with Denver and Salt Lake metros aligning to Midwest/West averages and non-metro areas running lower.

No single source provides a fully verified, city-by-city pricing matrix, so use these as a starting point and confirm against two or three local quotes before you commit.

How garage-door pros quote and collect this

For a routine spring or cable repair the price is easy; for a new door, the quote is the sale. The shops that win the door replacements are the ones that can show up, present clear good-better-best options on the spot, and make it painless to say yes. Claver for garage-door pros lets you build a repair-and-install pricebook once (springs, cables, openers by drive type, doors by material and size), send a clean quote from the driveway with the tariff-adjusted numbers already in it, take a deposit to lock the install on your schedule, and offer consumer financing when a $4,500 carriage door lands on a homeowner who came out expecting a spring repair, so the number you quote is the number you actually collect. See how the pieces fit on the garage-door page, or browse more cost guides in the guides hub.